Elantas PDG Sterling® E163 Single-Component Thixotropic Thermopoxy VPI Resin, 50 lb/5 gal
MFR #:117661
EIS #:PDGE16350LB
MFR #:117661
EIS #:PDGE16350LB
Low Stock
Min Qty:1
|Qty Increment:1
Elantas PDG Sterling® E163 Single-Component Thixotropic Thermopoxy VPI Resin, 1.2342 g/cm3 (77 °F (25 °C)) Density, 11.5% At 25 °C/77 °F Elongation, >94 °C (ASTM D93) Flash Point, 4 - 8 hr At 150 °C/302 °F Full Cure Time, 10 - 20 min At 150 °C/302 °F Gel Time, 74 Shore D Hardness, 5200 psi At 25 °C/77 °F Tensile Strength, 16000 - 22000 CP At 25 °C/77 °F, 2 rpm, 6000 - 8000 CP At 25 °C/77 °F, 20 rpm Viscosity. - Sterling® E 163 thixo is a single-component, heat-cured, epoxy impregnating resin.
$38.61 / US pound
Min Qty:1
|Qty Increment:1
Elantas PDG Sterling® E163 Single-Component Thixotropic Thermopoxy VPI Resin, 1.2342 g/cm3 (77 °F (25 °C)) Density, 11.5% At 25 °C/77 °F Elongation, >94 °C (ASTM D93) Flash Point, 4 - 8 hr At 150 °C/302 °F Full Cure Time, 10 - 20 min At 150 °C/302 °F Gel Time, 74 Shore D Hardness, 5200 psi At 25 °C/77 °F Tensile Strength, 16000 - 22000 CP At 25 °C/77 °F, 2 rpm, 6000 - 8000 CP At 25 °C/77 °F, 20 rpm Viscosity. - Sterling® E 163 thixo is a single-component, heat-cured, epoxy impregnating resin.
- Attributes
- Features
- Applications
- Documents
Attributes
General Information
Item NameThixotropic Thermopoxy VPI Resin
Trade NameSterling®
SeriesSterling® E163
General Features
Net Weight10.1 - 10.5 lb/gal
Shelf Life3 Months
TypeSingle-Component
Design & Construction
FormLiquid
Performance Details
Tensile Strength5200 psi
Full Cure Time4 - 8 hr at 150 °C/302 °F
Gel Time10 min
Technical Details
Flash Point94 °C
Chemical Properties
Viscosity16000 cP
Physical Properties
Container Size50 lb
Container TypePail
Elongation11.5% at 25 °C/77 °F
Hardness74 Shore D
Features
- Excellent thermal shock resistance
- Moisture and chemical resistant
- No catalyst required
- Thixotropic for minimal run-off
- Excellent penetration in VPI process
- Vacuum-pressure impregnation application methods
- Store below 25 °C / 77 °F in a dry controlled environment out of direct sunlight
- 8 - 12 Mils film build
- 50 °C heat deflection temperature
- 3.1% 24 hrs at 250 °C / 482 °F weight loss
- 0.04 at 60 Hz - 30 °C / 86 °F, 0.46 at 60 Hz - 60 °C / 140 °F dissipation factor
- 4.5 at 60 Hz - 30 °C / 86 °F, 7.6 at 60 Hz - 60 °C / 140 °F dielectric constant
- 1.8 x 10^12 Ohm-cm at 30 °C / 86 °F, 2.0 x 10^10 Ohm-cm at 60 °C / 140 °F volume resistivity
- Secondary insulation
- Gel Time: 8 - 15 min at 150 °C (302 °F)
- Container Size: 50 lb/5 gal
- Flash Point: >94 °C (ASTM D93)
- Viscosity: 16000 - 22000 CP at 25 °C/77 °F, 2 rpm, 6000 - 8000 CP at 25 °C/77 °F, 20 rpm
- Density: 1.2342 g/cm3 (77 °F (25 °C))
- Tensile Strength: 5200 psi at 25 °C/77 °F
- Gel Time: 10 - 20 min
- Viscosity: 16000 - 22000 cP
Applications
- Specifically Designed for Simultaneous Impregnation and Encapsulation of Stator Slots and End Windings