Elantas PDG Sterling® E069 Single-Component Thixotropic Epoxy Resin
- MFR #:Sterling® E069
- EIS #:PH21-Sterling E069
- MFR #:Sterling® E069
- EIS #:PH21-Sterling E069
Elantas PDG Sterling® E069 Single-Component Thixotropic Epoxy Resin, Epoxy Base Type, 1.2000 g/cm3 (77 °F (25 °C)) Density, 1350 V/Mil (ASTM D149), 1000 V/Mil (ASTM D149 After 24 hr in Water ) Dielectric Strength, >94 °C (ASTM D93) Flash Point, 6 hr At 149 °C/300 °F or 4 hr At 163 °C/325 °F Full Cure Time, 12 - 17 min At 150 °C/302 °F Gel Time, 84 (Shore D - 25 °C/77 °F) Hardness, 25000 - 55000 CP At 25 °C/77 °F, 2 rpm, 6500 - 11000 CP At 25 °C/77 °F, 20 rpm Viscosity. - Sterling® E 069 thixo is a single-component, heat-cured, 100% solids epoxy impregnating resin.
$38.14
- $44.96
Select from the options below
Elantas PDG Sterling® E069 Single-Component Thixotropic Epoxy Resin, Epoxy Base Type, 1.2000 g/cm3 (77 °F (25 °C)) Density, 1350 V/Mil (ASTM D149), 1000 V/Mil (ASTM D149 After 24 hr in Water ) Dielectric Strength, >94 °C (ASTM D93) Flash Point, 6 hr At 149 °C/300 °F or 4 hr At 163 °C/325 °F Full Cure Time, 12 - 17 min At 150 °C/302 °F Gel Time, 84 (Shore D - 25 °C/77 °F) Hardness, 25000 - 55000 CP At 25 °C/77 °F, 2 rpm, 6500 - 11000 CP At 25 °C/77 °F, 20 rpm Viscosity. - Sterling® E 069 thixo is a single-component, heat-cured, 100% solids epoxy impregnating resin.
Product Options
Showing 2 out of 2 options
 | Container Size: 500 lb | EIS Part #: PDGE069DRUM | $ / US pound | |
| Container Size: 50 lb | EIS Part #: PDGE0695G | $ / US pound |
- Attributes
- Features
- Applications
- Documents
Attributes
General Information
Item NameThixotropic Epoxy Resin
Trade NameSterling®
SeriesSterling® E069
General Features
Net Weight9.8 - 10.2 lb/gal
Shelf Life3 Months
TypeSingle-Component
Design & Construction
Base TypeEpoxy
FormLiquid
Performance Details
Full Cure Time6 hr at 149 °C/300 °F or 4 hr at 163 °C/325 °F
Gel Time12 min
Technical Details
Flash Point94 °C
Chemical Properties
Viscosity25000 cP
Electrical Properties
Dielectric Strength1350 V/mil
Physical Properties
Hardness84 Shore D at 25 °C/77 °F
Features
- High build
- Low run-off
- Fiber-reinforced for toughness and thermal shock resistance
- Chemical and moisture resistant
- No catalyst required
- Vacuum-pressure impregnation application methods
- Store below 25 °C / 77 °F in a dry controlled environment out of direct sunlight
- 0.005 at 1 kHz - 25 °C/77 °F and 1 kHz - 50 °C/77 °F, 0.02 at 1 kHz - 100 °C/212 °F, 0.99 at 1 kHz - 150 °C/302 °F dissipation factor
- 3.0 at 1 kHz - 25 °C/77 °F and 1 kHz - 50 °C/77 °F, 3.2 at 1 kHz - 100 °C/212 °F, 4.7 at at 1 kHz - 150 °C/302 °F dielectric constant
- 1.3 x 10^16 Ohm-cm at 25 °C/77 °F volume resistivity
- 10 - 13 Mils film build
- 81 Pounds at 25 °C/77 °F, 14 Pounds at 150 °C/302 °F helical coil bond strength (ASTM D2519 over MW 35)
- Secondary insulation
- Gel Time: 12 - 17 min at 150 °C/302 °F
- Dielectric Strength: 1350 V/Mil (ASTM D149), 1000 V/Mil (ASTM D149 After 24 hr in Water )
- Flash Point: >94 °C (ASTM D93)
- Viscosity: 25000 - 55000 CP at 25 °C/77 °F, 2 rpm, 6500 - 11000 CP at 25 °C/77 °F, 20 rpm
- Density: 1.2000 g/cm3 (77 °F (25 °C))
- Gel Time: 12 - 17 min
- Viscosity: 25000 - 55000 cP
Applications
- Impregnation and Encapsulation of Motor Stators